| Tanzer 22 Specifications - Standard Equipment Hull and Deck - Single unit fiberglass hull, hand-laid of woven roving alternated with mat. - Single unit fiberglass deck, cabintop and cockpit reinforced throughout with sandwich construction, ensuring a rigid, well-insulated, non-flexible deck and quiet interior. - Non-skid on deck cockpit floor and seats. - Teak handrails and companionway dropboards. - Aluminum framed, tinted acrylic foredeck hatch with gas tank cover, main companionway hatch and cockpit locker hatches (P-S) in fiberglass with interior liners and lockable safety hasps. - White vinyl rub rail around gunwale. - Contrasting water line - boot top and sheer stripe colors molded in. Ballast - Through-bolted fin keel or optional keel - centerboard; both in cast iron. - Centerboard of keel C-B is housed in the keel below the hull with retraction winch in cockpit. Rudder - Streamlined outboard rudder molded in fiberglass. - Lifting ash and mahogany laminated tiller. - Stainless steel gudgeons and pintles. Spars - Anodized aluminum mast with integral sail track and gate. - S-S masthead fitting, shroud tangs and spreader bases. - Aluminum spreaders. - Gooseneck track. - Main and jib halyard cleats with mast straps to retain halyard rope tails. - Hinged mast step. - Anodized aluminum boom with sail track, gooseneck and clew outhaul cleat. - Mast is grounded to keel. Standing Rigging - 5-32" 1 x 19 S-S wire with S-S turnbuckles and toggles. Running Rigging - Main halyard 3-32" 7 x 7. - Jib halyard 1-8" 7 x 19 S-S wire with Dacron rope tails. - Topping lift 3-32" 1 x 19 S-S wire. - Main and jib sheets in 3-8" dia. braided Dacron. Sails - Mainsail and working jib in 5 oz. (US) white Dacron with class insignia, sail number, battens and sail bag. Deck Fitting and Hardware - All deck fittings are through-bolted with S-S fastenings and consist of a custom-designed bow pulpit, stemhead fitting, backstay and shroud chainplates with covers, all in stainless steel; two bow chocks (P-S), bow mooring cleat and two stern mooring cleats (P-S). - Self-draining anchor stowage well with cover. - Aluminum tracks with adjustable slides and non-tumbling blocks and cleats (P-S) for working jib sheets. - Main companionway dropboards in solid teak with two screened vents and lockable hasp. - Four fixed ports in main cabin, two in forecabin. - S-S mainsheet block with jamb cleat. - Genoa rack and stops. - A non-corrosive outboard motor bracket to lift motor clear of water when under sail is installed on transom for 6 hp long shaft motor. - Coaming stowage compartments are fitted in each side of the cockpit. Interior - Four wide, full-length berths with 4" fabric covered cushions and choice of colors. - One-piece white molded fiberglass interior liner and full headliner. - Dinette table and seats. - Galley unit and countertop with 2 1-2 cu. ft. self-draining icebox, galley sink, fresh water pump and 10 gallon water tank. - Cutlery and crockery stowage lockers - Shelves in main cabin (P-S). - Cabin sole carpeted. - Teak bulkhead separating main and forecabins. Cockpit - Unusually large self-draining cockpit 7' 9" x 6' 3". - Two large, lockable stowage lockers (P-S). - A lockable self-draining gas tank locker at the aft end of the cockpit. Electrical System - Heavy-gauge 12V DC wiring, fuse panel and fixtures with wet cell battery provides interior lighting and bow light. Hull and Deck Colors - Standard White (852) hull, deck, interior and headliner. - Sheer stripe and waterline - boot top in either red (259), royal blue (564), medium blue (550), light blue (591), dark green (452) or yellow (350). - Choice of other colors charged extra. Warranty - Twelve-month limited warranty. |
