Although relatively complex compared to their forebears, modern outboard motors are more reliable than ever before, and a well-looked after engine will give reliable service. The most likely problems are found with the battery or electrical system, resulting in a failure to start. The procedure for pinpointing and rectifying such a problem is similar to that for diesel engines – see Solve Your Diesel Engine Problems: Fuel, Air, Starting, Wiring.

There are also many older engines – some two or three decades old – in regular use. These have the potential to be equally reliable, but lack the sophisticated electronics that produce a strong spark at the optimum moment for combustion, and in the case of two-stroke motors, frequently the oil must be pre-mixed with the fuel in the tank.

removing-carburetor

It's sometimes necessary to remove the carburetor from your outboard.



Starting an older motor

More modern engines with sophisticated fuel injection systems or automatic chokes tend to start easily. However, smaller and older models may need a little coaxing. In any case it’s always worth consulting the motor’s operating manual – these are often available even for older engines that have been out for production for 30 years.

Before starting, make sure the throttle is in the 'start’ position, the fuel is turned on, the vent for the tank is open, and if it's a remote tank give a couple of squeezes of the bulb in the fuel line. The start cord is often longer than most operators realize – make sure you’re standing somewhere where you’re well braced and can give a really long pull.

Two-stroke motors are likely to need choke for a maximum of only a couple of seconds after the engine fires – as soon as you’ve let go of the starter cord, put your hand on the choke and be ready to flick it to the running position immediately after the engine revs start to dip. With a relatively small four-stroke motor with a pull start, it can help to turn the engine gently a couple of times before starting; the choke is then likely to be needed for longer than a two-stroke – maybe 10-20 seconds.

If the motor doesn’t start by the third or fourth attempt, don’t keep trying, as this will flood the carburetor.  If you can smell fuel, then this has probably already happened. The easiest solution is to wait for 5-10 minutes, but if time is of the essence it may be possible to start the motor by switching the choke to the running position and pulling the starter cord several times.

Removing the carburettor float

Removing the carburetor float.



Fuel system problems

The most likely problems to beset older two-stroke outboard engines are with the fuel system. Modern fuels have a shelf life of only a few months, especially when mixed with two-stroke oil, with the fuel leaving a black varnish or gum on the inside of the carburetor when it evaporates. A build-up of this will gradually restrict the size of the carb’s main jet, which means the motor won’t receive all the fuel as it needs. The classic symptom of this problem is a motor that misfires and runs roughly, with loss of power even when warm, but improving when given choke. Even with choke it will not be capable of delivering full power, but it should serve to get you home.

There are two simple ways of avoiding trouble. One is to always keep the carburetor wet with fuel – if the boat is used weekly during the season then there will be no problem; similarly if you visit the boat weekly and it has a remote fuel tank, a couple of squeezes of the priming bulb will keep the carb wet, even if the engine is not run. Adding fuel stabilizer will prolong the life of the fuel, and reduce the tendency to produce varnish.

dismantled carburetor

The dismantled carburetor.



The second option is to remove all the fuel from the carb after using the engine, so there’s none left to evaporate. Many carburetors are fitted with a drain plug that can be removed to allow all the fuel to run out. On other engines it’s possible to turn the fuel supply off and allow the motor to die when the fuel in the carburetor bowl runs out – but always check the engine manual first to confirm there’s no risk of the procedure damaging the motor.

If you do have problems, you’ll need to clean the carburetor jets – this is a straightforward task, but in most cases it means removing the unit from the engine. Start by removing the air cowling, then disconnect the choke linkage, throttle cable, and fuel line. The nuts holding the unit in place can then be unscrewed; if you drop one, make sure you recover it before removing the carburetor.

Then turn the carburetor upside down and remove the screws holding the bowl in place. With this removed, the plastic float can be lifted out, along with the hinge pin for the lever above the needle jet. It’s now possible to see the condition of both jets – if these are dirty they should be soaked overnight in carb cleaner, then cleaned with a blast of compressed air.

Shear pin or hub insert
To prevent gearbox damage if the propeller strikes a solid object, the prop of an older outboard is driven via a shear pin, a weak link that breaks before anything else in the system. Such engines normally have provision for carrying spares under the engine cowling – it’s worth carrying a few. They can be quickly replaced after removing the prop, but make sure there’s no chance anyone can start the engine while you’re working on it.

Newer and larger engines normally have a rubber hub insert in the prop that absorbs small knocks. These are more resilient to absorbing knocks without damage, but if failure does eventually occur, there’s no quick fix as with a shear pin.

shear pin

The shear pin is designed to break before anything else to prevent serious damage to your engine.



Need some engine parts to get the job done? Visit the Boats.com Gear and Parts Store.

Rupert Holmes has cruised and raced more than 60,000 miles, between 60 degrees north and 56 degrees south. He writes about all aspects of boat ownership and marine travel, including destinations, seamanship, and maintenance, as well as undertaking regular boat and gear tests. He owns two yachts, one currently based in the Aegean and the other in the Solent.

This story originally appeared on uk.boats.com.

Written by: Rupert Holmes
Rupert Holmes has more than 70,000 miles of offshore cruising and racing experience, in waters ranging from the North Sea to the Southern Ocean and Cape Horn. He writes about all aspects of boat ownership and marine travel, including destinations, seamanship and maintenance, as well as undertaking regular new boat and gear tests. He currently sails around 5,000 miles per year and in the past couple of seasons has cruised from the UK to the Azores, as well as winning his class in the 2014 two-handed Round Britain and Ireland Race. He also owns two yachts, one based in the Mediterranean and the other in the UK.
Advertisement